UF保养操作卡


    UF装置保养操作步骤
    1 清洗UF清洗装置
    1) 开清洗水箱工业水进水阀启动二级RO水泵清洗水箱注满水关闭
    2) 开清洗水泵(1#2#)进口门出口门循环门启动清洗水泵洗水箱10min
    3) 停止洗水泵开清洗水箱排污门水排空开清洗水箱工业水进水门清洗水箱进满水
    4) 开保安滤器进水门保安滤器UF装置清洗出口门关闭循环门开UF清洗进口门浓水侧清洗回流门产水侧回流门
    5) 启动清洗水泵清水试验清洗回路
    2 UF装置排空:开UF排门排门产水排放门UF装置排空
    3 保安滤器装置排空:开保安滤器排空阀排污阀滤器水排空
    4 配置保护液:亚硫酸氢钠100kg开工业水进水门水位14m(浓度1)开清洗水泵进出口门循环门关闭保安滤器进口门启动清洗水泵循环30mins药液充分溶解
    5 循环:
    1) 开UF清洗进口门浓水侧清洗回流门产水侧清洗回流门
    2) 开清洗水泵(1#2#)进口门出口门保安滤器进口门关闭保安滤器UF装置清洗出口门开保安滤器排空门
    3) 启动清洗水泵(1#2#)排空门药液排出时开保安滤器UF装置清洗出口门关闭排空门
    4) UF注入保护液循环保护液1时
    6 浸泡:停清洗水泵关闭UF清洗进口门浓水侧清洗回流门产水侧清洗回流门
    7 洗:
    1) 洗清洗水箱
    a) 开清洗水箱工业水进水阀启动二级RO水泵清洗水箱注满水关闭
    b) 开清洗水泵进口门出口门循环门启动清洗水泵洗水箱10min
    c) 停泵开清洗水箱排污门水排空
    d) 开清洗水箱工业水进水门清洗水箱进满水
    2) 洗清洗保安滤器清洗液进药路
    a) 关闭循环门开清洗保安滤器UF出口门关闭清洗液浓水侧回流门清洗液产水侧回流门开排门产水排放手动门
    b) 启动清洗水泵保安滤器进药路清洗液顶出
    c) 清洗水箱水位处低位时停止清洗水泵
    3) 洗UF装置
    a) 开UF排门产水排放手门进水门启动超滤水泵洗水质合格
    b) 开UF洗门产水排放手门启动超滤水泵洗水质合格
    4) 洗清洗装置回流道
    a) 开UF进水门浓水侧清洗回流门产水侧清洗回流门关闭清洗进水门UF产水排放门UF浓水排放门
    b) 启动UF水泵洗清洗装置道清洗箱5min
    注:化学保养期间UF装置切换状态禁止操作


    UF unit preservation procedure
    1 Flush the UF cleaning unit
    1) Open the clear water inlet valve start the secondary RO feed pump filling the flushing tank with the clear water
    2) Open the flushing pump inlet valve and outlet valve circulation valve start the flushing pump to flush the flushing tank for 10mins
    3) Stop the flushing pump open the flushing tank blow down valve and discharge the dirty water in the flushing tank Open the clear water inlet valve filling the flushing tank with the clear water
    4) Close the circulation valve open the safety filter inlet valve the safety filter to UF outlet valve the UF washing liquid inlet valve1# UF washing liquid outlet valve and 2# UF washing liquid outlet valve start the flushing pump checking the pipeline
    2 Discharge the safety filter open the safety filter air vent valve and blow down valve
    3 Discharge the UF unit open the UF up drain valve the down drain valve UF outlet drain valve
    4 Prepare the preserve liquid open the clear water inlet valve make the liquid level equal to 14m put the 100kg NaHSO3 into the flushing tank open the flushing pump inlet valve and outlet valve circulation valve close the safety inlet valve start the flushing pump to dissolve the chemical absolutely for 30mins
    5 Circulation
    1) Open the UF washing liquid inlet valve 1# UF washing liquid outlet valve and 2# UF washing liquid outlet valve
    2) Open the flushing pump inlet valve and outlet valve close the circulation valve open the safety filter inlet valve close the safety filter to UF outlet valve and open the safety filter air vent valve
    3) Start the flushing pump when the preserve liquid drain from the air vent valve open the safety filter to UF outlet valve and close the air vent valve
    4) Circulate the preserve liquid between the flushing device and UF unit one hour and stop the flushing pump
    6 Preservation stop the flushing pump close the UF washing liquid inlet valve 1# UF washing liquid outlet valve and 2# UF washing liquid outlet valve
    7 flushing
    1) Flush the UF cleaning device
    a) Open the clear water inlet valve start the secondary RO feed pump filling the flushing tank with the clear water
    b) Open the flushing pump inlet valve and outlet valve circulation valve start the flushing pump to flush the flushing tank for 10mins
    c) Stop the flushing pump open the flushing tank blow down valve and discharge the dirty water in the flushing tank
    d) Open the clear water inlet valve filling the flushing tank with the clear water
    2) Flush the flushing safety filter and chemical cleaning liquid inlet pipeline
    a) Close the circulation valve open the flushing safety filter to UF outlet valve close the1# UF washing liquid outlet valve and 2# UF washing liquid outlet valve Open the up drain valve and the outlet drain valve
    b) Start the flushing pump flushing the flushing safety filter and chemical cleaning liquid inlet pipeline
    c) Stop the flushing pump when the flushing tank liquid level is low
    3) Flush the UF unit
    a) Open the UF up drain valve outlet drain valve inlet valve start the UF feed pump flush the UF unit
    b) Open the UF inlet flashing valve outlet drain valve start the UF feed pump flush the UF
    4) Flush the UF flushing backflow pipeline
    a) Open the UF inlet valve 1# UF washing liquid outlet valve and 2# UF washing liquid outlet valve
    b) Close the washing liquid inlet valve the UF outlet drain valve and up drain valve
    c) Start the UF feed pump flush the UF flushing device pipeline and flushing tank 5min

    Attention during the UF unit is preserved any operation is banned
    文档容仅供参考
    文档香网(httpswwwxiangdangnet)户传

    《香当网》用户分享的内容,不代表《香当网》观点或立场,请自行判断内容的真实性和可靠性!
    该内容是文档的文本内容,更好的格式请下载文档

    下载文档到电脑,查找使用更方便

    文档的实际排版效果,会与网站的显示效果略有不同!!

    需要 2 香币 [ 分享文档获得香币 ]

    下载文档

    相关文档

    设备预检修保养卡

     设备预检修保养卡 设备名称: 单位: ...

    11年前   
    26927    0

    电动空压机,操作,保养,规程

    本标准规定了电动空压机运行操作的基本要求及维护、保养的内容。

    5年前   
    1155    0

    折边机操作保养规程

    熟悉折边机的工作原理,基本构造,熟练掌握折边机的操作技能和保养要求。

    5年前   
    1328    0

    电动水泵操作保养规程

    本标准规定了公司各类电动离心泵、多级离心泵运行操作的基本要求及维护、保养的内容。

    5年前   
    1050    0

    施工机械操作保养规程

    3.1.1 操作人员应体检合格,无妨碍作业的疾病和生理缺陷,并应经过专业培训。学员应在专人指导下进行工作。

    5年前   
    1188    0

    剪板机操作保养规程

    3.1.1 熟悉剪板机的工作原理,基本构造,熟练掌握剪板机的操作技能和保养要求。

    5年前   
    1431    0

    金属切削机床操作保养规程

    1 范围本标准规定了金属切削机床运行操作的基本要求及维护、保养的基本内容。本规程适用于公司各型号的车床、刨床、铣床、摇臂钻床等金属切削机床。2 规范性引用文件CA6140车床使用说明书JGJ33...

    5年前   
    1166    0

    磁力钻操作保养规程

    本标准规定了磁力钻运行操作的基本要求及维护、保养的基本内容。

    5年前   
    1532    0

    炉顶吊操作保养维护规程

    1 范围本标准规定了电站扳起塔式起重机运行操作的基本要求及维护、保养的内容。本规程适用于公司300MT-2型炉顶吊。2 规范性引用文件300MT-2炉顶吊随机说明书DL5009.1-2002 ...

    5年前   
    908    0

    电动卷扬机操作保养规程

    1 范围本标准规定了电动卷扬机等机械运行操作的基本要求及维护、保养的内容。本规程适用于公司JJK、JMW、JM系列型号的1-10t电动卷扬机2 规范性引用文件电动卷扬机机械使用说明书DL5009...

    5年前   
    1092    0

    柴油空压机的操作保养规程

    本标准规定了柴油空压机的运行操作的基本要求及维护、保养的内容。

    5年前   
    1506    0

    卷板机操作保养规程

    熟悉卷板机的工作原理,基本构造,熟练掌握剪板机的操作技能和保养要求。

    5年前   
    1326    0

    铣钻床机械操作保养规程

    1 范围本标准规定了机械运行操作的基本要求及维护、保养的内容。本规程适用于ZX7032型铣钻床。2 规范性引用文件ZX7032型铣钻床机械使用说明书JGJ33-2001 ...

    5年前   
    1063    0

    螺栓套丝机操作保养规程

    本标准规定了螺栓套丝机运行操作的基本要求及维护、保养的内容。

    5年前   
    987    0

    《1.2太阳对地球的影响》操作卡

    **三中236教学模式学生自主学习操作卡

    4年前   
    812    0

    平衡计分卡操作手册

    长庆油田分公司平衡计分卡操作手册人事处〔组织部〕/联合工程组2006年11月目 录第一局部 平衡计分卡认识与理解 41. 平衡计分卡的诞生与开展 41.1. 诞生背景 41.2. 开展历程 ...

    10个月前   
    234    0

    世界五百强表格——设备修理保养情况记录卡

    设备修理保养情况记录卡 编号设备名称机器编号厂 ...

    9年前   
    535    0

    挤出机设备操作工须知及保养计划

    挤出机设备操作工须知及保养计划挤出机设备生产操作工,是维护保养设备、延长挤出机工作寿命的主要负责人。每个操作工都应该明白,减少挤出机维修、更换零件次数、延长挤出机工作使用年限,是降低生产塑料制...

    3年前   
    515    0

    机动叉车安全操作规程与保养制度

    机动叉车安全操作规程与保养制度一、 目的:}{7nvC为了维护设备完好和安全使用,保证机动叉车驾驶安全。二、 7X*lCpxv7__ d适用范围:8WJ“_C?n7j$v$r~本规程适用...

    3年前   
    751    0

    厂内小型机动车辆操作保养规程

    1 范围本标准规定了厂内小型机动车辆运行操作的基本要求及维护保养的内容。本规程适用于公司FC1A机动反斗车、江淮180型拖拉机头。2 规范性引用文件FC-1A机动翻斗车、江淮180拖拉机机头使用...

    5年前   
    828    0

    文档贡献者

    文***品

    贡献于2022-05-09

    下载需要 2 香币 [香币充值 ]
    亲,您也可以通过 分享原创文档 来获得香币奖励!
    下载文档

    该用户的其他文档